UP↑SCALE › SCALES & ADAPTERS › MAKERS & DEVELOPERS

For makers and developers

Two maker boards, four wires, our firmware - and your scale is on the air. The protocol is open, ESP-NOW talks to your own ESP32 projects, and the example code gets you going in an evening. The UP↑SCALE firmware runs on ESP32-S3 and ESP32-C3 boards and is free to use.

  • A DIY adapter from two maker boards
  • An open protocol with example code
  • ESP-NOW for your machines and displays
  • USB serial for your own software

In short

UP↑SCALE is one scale app with its own firmware for ESP32 boards. Makers build their own RS-232 adapter from two maker boards for under 15 EUR, read the open, documented protocol and connect the scale to their own web pages, Arduino and ESP projects over Bluetooth, ESP-NOW or USB. Firmware and app are free to use; PRO from 4.43 EUR a month or 119.90 EUR once, only when you want more.

What helps you most

1Build the adapter yourself - about 15 EUR

An ESP32-S3 or ESP32-C3 board with at least 4 MB flash and a 3.3 V RS-232 board, four jumper wires - no soldering with pre-soldered boards. The firmware installs from the browser and finds out by itself which chip it is; the pins are set in the app. Same app, same licence as the ready-made adapter.

2An open wireless protocol FREE

The scale sends its weight, state and page as small packets and takes simple commands (tare, OK, page switch, settings). Read it from your own web page with a few lines of JavaScript, or from any device that speaks the low-energy radio. With BLE FOR ALL the scale also sends its weight openly to every device nearby - no connection needed.

3ESP-NOW: scale to machine, peer-to-peer TRY 14 DAYS FREEPRO

Switch on ESP-NOW and the scale sends to (and listens to) your own ESP32 devices directly - no router, no pairing, many at the same time. Every packet is encrypted with the own key of your device: one line from the app that you paste into your sketch. Displays, relays, valves, sorting gates, a pump for the espresso early stop. The factory mode drives your machine with a predictive cut-off.

4USB serial for your own software FREE

Over USB the scale sends its values as text - for data loggers, standard scale software, a Raspberry Pi or your Python script - and takes single-character commands (tare, OK, navigation).

5Example code to start from

Tips from the practice

  • Never a 5 V RS-232 board (MAX232 without the "3"): it puts 5 V on the RX pin of the ESP32.
  • RX and TX the wrong way? SWAP TX/RX in the app - no need to change the wires.
  • Start free: the firmware and the app are free to use; PRO only when you want more.

Two scales and a machine in the app

Two scales added up to one weight over Bluetooth - and a filling machine over ESP-NOW with a cut-off that learns its lag.

Two scales in the weighing mode: 500.00 g on scale 1 and 12.35 g on scale 2, together 512.35 g with all nutrition values
Two scales, one sum: 512.35 g
The cut-off of the filling machine with the learned lag, slow down 15 percent before the target and a pause of 2 seconds - and the totals: 7 cavities of 20 g, every one a little above the target, plus 0.3 g on average
Never under: +0.3 g per cavity on average

More about the app, with all screenshots →Screenshots of the real app with demo values - a screenshot may show the look of an older app version.

For makers and developers: questions and answers

How do I build an ESP32 RS-232 adapter for my scale?

Take an ESP32-S3 or ESP32-C3 board with at least 4 MB flash and a 3.3 V RS-232 board, and connect them with four jumper wires - no soldering with pre-soldered boards. Install the firmware from the browser (it finds out which chip it is) and set the pins in the app. About 15 EUR in parts: parts list and wiring.

Which RS-232 board can I use with an ESP32?

A 3.3 V board (MAX3232 or SP3232 chip). Never a 5 V board with a MAX232 (without the "3"): it puts 5 V on the RX pin of the ESP32. RX and TX the wrong way round? SWAP TX/RX in the app, no need to change the wires.

How do I read the weight of a Bluetooth scale in JavaScript?

With Web Bluetooth: the UP↑SCALE protocol is open, the scale sends its weight, state and page as small packets and takes simple commands (tare, OK, page switch). A few lines of JavaScript on your own page read it; the example code shows the combined weight of all scales around you. With BLE FOR ALL the scale also sends its weight openly to every device nearby, without a connection.

Can the scale talk to my own ESP32 over ESP-NOW?

Yes. With ESP-NOW the scale sends to and listens to your own ESP32 devices directly - no router, no pairing, many at a time. Every packet is encrypted with the own key of your device, one line from the app that you paste into your sketch. Displays, relays, valves, sorting gates, a pump for the espresso early stop.

Can I read the scale over USB from Python or a Raspberry Pi?

Yes. Over USB the scale sends its values as text - for data loggers, standard scale software, a Raspberry Pi or your Python script - and takes single-character commands for tare, OK and navigation.

Is the firmware open source?

No, the firmware is our own - but it is free to use, and the app too; PRO only when you want more. The protocol is open and documented with example code for HTML / JavaScript and Arduino / ESP32.

Is a self-built adapter as good as the ready-made one?

It runs the same firmware with the same app and the same licence as the ready-made adapter, and the licence is bound to your chip.

Last updated · by Johann Anderson, FARM 23 SL

READY TO UP↑SCALE YOUR SCALE?

Start with the free version - the board costs under 15 EUR and you may never need more. If you do, unlock PRO from 4.43 EUR a month, 46.90 EUR a year or once for 119.90 EUR incl. VAT - or ENTERPRISE & COMPLIANCE from 13.00 EUR a month (once: 599.00 EUR). The lifetime licences are once and forever, no subscription needed; no advertisements, everything works offline, updates stay free.